AL8010F-THERMOSTAT-FOR-SALE_tn

Elitech AL8010F thermostat owns 1 output relay to connect the refrigerator or a heater, the controllable temperature range from -50 to 120 ℃.

AL8010F Refrigeration or Heating Digital Thermostat


MOQ: 100 USD


Features of the AL8010F

  • Two types of wiring methods, The input power voltage for this temp controller and the load could be different;
  • The temperature set-point (-50 to 120 ℃) and the hysteresis to determine the target temperature range, and the high & low limit to the Temperature Set-point available;
  • Embed NVM to auto memory exists parameters, resume all data once power back, need not configure it again;
  • Adjustable Temperature Calibration;
  • Editable compressor protection delay time;
  • Alarm by error code on display (without buzzer inside) once the sensor temperature exceeds the measurable range or sensor error.

Front Panel of AL8010F Thermostat

blank

blank

blankThe resolution is 0.1 °C from 0 to 99.9, just 1°C out of this range, since only 3 digital tubes on the screen.


AL8010F temperature controller Wiring Diagram

This unit exist two ways to wiring

  • the left wiring diagram with the same input power supply 220V,
  • the right diagram with different voltages, the loads could connect 110V, but the controller must power 220V (assume you buy the 220V, you can also buy other versions, e.g. 24v)
2021 New AL8010F wiring diagrams
2021 New AL8010F wiring diagrams
AL8010F digital thermostat for regulate temperature by control the working status of Heating or Cooling load - wiring diagram and photo
AL8010F Thermostat - wiring diagram photo

Function Menu of AL8010F Temp Controller

CodeFunctionMinMaxDefaultUnit
HCRefrigeration or Heating ModeCHC
DTemperature Hysteresis / Return Difference1155°C
LSLower Limit for Set-Point-50SP-50°C
HSUpper Limit for Set-PointSP120120°C
CATemperature Calibration-550°C
PTProtection Delay Time for Refrigeration0101Min

How to set the aimed temperature range?

The aimed temperature range consists of two parts: “SP – D” as the bottom line, and “SP + D” as the top line, Hence, you need to set both the “SP” and the “D”(Hysteresis)

  • SP is the temperature set-point; check it by pressing the "set" key in normal working status, then configure it by pressing the "UP" and "DOWN" keys; Press the "RST" key to save the new data.
  • Hold the "set" key for 3 seconds to enter into the function menu interface, find out the “D”, and change it, remember to save the new value.
  • When HC = C, it is the refrigeration controller mode, the the “PT” (protection time for the compressor) option works;
  • hen HC = H, it is just a heating controller; the PT is useless.

Error Code of AL8010F

There is no buzzer inside of AL8010F temperature controller. Therefore it just shows an error code on display.

  1. "- - -" means sensor error or open circuit;
  2. "HHH" caused by the room temperature exceeds the upper limited or sensor short circuit;
  3. "LLL" means the measured temperature by the thermistor lower than the bottom limited or sensor short circuit;

AL 8010F Controller User Manual Download

Share to Unlock Contentimage/svg+xml
Unlock this exclusive content by using one of the sharing buttons below.

Tip: This User instruction was created based on the Elitech AL8010F thermostat, we can not assure you this brochure also works to the same models from other manufacturers.

 


FAQ of Haswill Compact Panel Thermostat

  1. How to get the price?
    Click the inquiry button, and finish the form, you will get a reply in 24 hours.
  2. Celsius VS Fahrenheit
    All of our digital temperature controllers default in Celsius degree, part of them available in Fahrenheit with MOQ.
  3. Parameter Comparison
    Compact panel digital temperature controllers tables
  4. Package
    The common package could load 100 PCS / CTN digital temperature controllers.
  5. Accessories
    We suggest you buy 5% ~ 10% spare parts like clips and sensors as stock.
  6. Warranty
    Default one-year (extendable) quality warranty to all our controllers, we will offer free-of-charge7. replacement if found a quality defect.
  7. Custom-Made temperature controller
    If you can not find suitable temperature controllers from this website, please contact us for a custom-made service, the MOQ is usually from 1000PCS.

more questions? Click FAQs



MOQ: 100 USD